New HampshireBusinessesNear Me
Why Is My Furnace Not Heating? A New Hampshire Homeowner's Checklist
← All Posts

hvac

Why Is My Furnace Not Heating? A New Hampshire Homeowner's Checklist

Furnace out in New Hampshire? Follow this check order from thermostat and filter to oil resets and flame sensors, plus gas, CO, and frozen pipe safety steps.

·November 11, 2026·9 min read

Why Is My Furnace Not Heating? A New Hampshire Homeowner's Checklist

If a carbon monoxide alarm is sounding, leave the house now, get everyone to fresh air, and call 911. The New Hampshire State Fire Marshal's Office says to evacuate first, and headaches, dizziness, or nausea that ease when you step outside are reason to get medical help. Do not go back in until responders say it is safe.

If you smell gas, leave without touching light switches or appliances, and call from outside. Liberty's natural gas customers in New Hampshire can reach its emergency line at 1-855-327-7758 or dial 911, and propane customers should call 911 or their supplier from a safe distance. Everything below assumes no alarm is sounding and nothing smells wrong.

Check the Thermostat Before Anything Else

Plenty of no-heat calls end at the wall. Make sure the thermostat is set to Heat, set it about five degrees above the room temperature, and replace the batteries if the screen is blank or dim. If the fan runs but no heat comes, check that the fan setting is on Auto rather than On, because On will blow cool air between cycles.

Give the system a few minutes to respond. Most furnaces go through a sequence of draft motor, ignition, and blower that takes a minute or more before warm air arrives. A smart thermostat that has lost its Wi-Fi may also still be following an old schedule, so try the manual override.

Power Switches and Breakers

Most furnaces have a service switch that looks like an ordinary light switch, mounted on or near the unit or at the top of the basement stairs. It gets bumped more often than you would expect, especially in a basement that doubles as storage. Oil burners often have a separate red-plated emergency switch as well.

Next, check the breaker panel and reset a tripped furnace breaker once. If it trips again, leave it off and call a technician. Also check that the blower door panel is seated, because a safety switch keeps the furnace from running when that panel is loose.

Look at the Filter

A clogged filter chokes airflow, and the furnace can overheat and shut itself off on a safety limit. Pull it out and hold it up to a light. If you cannot see light through it, replace it, then give the system a few minutes to cool before trying again.

One-inch filters generally need changing every one to three months in a heating season, and more often with pets, wood dust, or renovation work nearby. If heat comes back and shuts off again within a few minutes, the filter was probably not the only problem. Check that supply registers and return grilles are open and not blocked by furniture.

Have You Run Out of Fuel?

New Hampshire heats with more oil than most of the country. Federal energy data puts fuel oil at roughly four in ten households, with natural gas and propane near one in five each, so the fuel check depends on where you live. Manchester, Nashua, and Concord have natural gas service in many neighborhoods, while the North Country and rural towns rely more on oil, propane, and wood.

Read the oil tank gauge first, and do not trust it completely if it is old. An oil tank that runs dry can also pull air and sludge into the line, so the burner may not restart even after a delivery. Your oil company can usually bleed the line and restart it, and many offer emergency deliveries for a fee, so ask about that when you call.

Propane has its own wrinkle. If the tank ran completely out, your supplier may need to do a leak check on the system before turning the gas back on, so do not try to relight appliances yourself. On natural gas, check that the shutoff valve near the furnace is parallel to the pipe and ask your neighbors or the utility whether there is an outage.

The Oil Burner Reset Button

The red button on the burner's primary control is a lockout reset, and it should get one press only. Every failed start can spray oil into the combustion chamber, and repeated resets can leave unburned fuel that ignites all at once, an event technicians call a puffback. That can fill a house with soot or cause a more dangerous failure.

Press it once after confirming you have oil. If the burner does not run, or locks out again, call for service. Some modern controls lock out permanently after several tries, and that takes a technician to clear anyway.

Blocked Vents and Snow

High-efficiency gas and propane furnaces often vent through a sidewall with plastic pipes, and those outlets can get buried. A January storm in Concord or a drift against the house can block intake and exhaust, and the pressure switch will stop the furnace from firing. Clear snow and ice gently from around both pipes, and keep the area clear for the rest of the winter.

Chimney-vented oil and gas systems can have their own trouble, from a blocked flue to a failed draft regulator. Do not run a furnace you suspect has a venting problem, since that is how carbon monoxide gets into living space. Have CO alarms outside every sleeping area and on every level, as the state fire marshal recommends.

Condensing furnaces also drain water through a small line, and if that line freezes or clogs, a safety switch can shut the system down. Look for standing water near the furnace or a sagging drain line through an unheated space. A line that freezes more than once should be rerouted or insulated.

Flame Sensor and Ignition Problems

Gas and propane furnaces that light for a few seconds and then shut off often have a dirty flame sensor. That thin metal rod sits in the burner flame and tells the control board the gas has lit, and a coat of residue can keep it from reading correctly. A handy owner can clean it with fine steel wool or light abrasive after shutting off power and gas, though a technician will also check the rest of the sequence.

If you never see a flame, the igniter may be the cause. Hot surface igniters are brittle and wear out, and most newer furnaces use one in place of a standing pilot. If your older unit has a pilot that will not stay lit, the thermocouple could be at fault, and a repeated failure should get a service call.

Open the panel and read the status light if your furnace has one. The blink pattern points to a specific fault listed on a chart inside the door, and giving that code to the technician can save time on the call. Replacing gas parts past this point is a job for a pro, since New Hampshire licenses fuel gas fitters through its Mechanical Safety and Licensing Board.

On an oil furnace, frequent lockouts usually point to a clogged nozzle, a dirty filter, or a failing igniter or cad cell. These parts wear out on a schedule, which is why an annual tune-up matters so much. The fire marshal's office also recommends having heating systems serviced every year.

Old Houses, January Cold, and Frozen Pipes

An old New England farmhouse with fieldstone or thin wall cavities can lose heat fast. In a January cold snap, particularly in the North Country where nights can fall well below zero, pipes along exterior walls and in crawlspaces can freeze within hours of losing heat. Call for service early rather than waiting until morning, and tell the dispatcher you have no heat.

While you wait, open cabinet doors under sinks on outside walls and let faucets run at a slow drip. Close off unused rooms, hang blankets over drafty doors, and use space heaters only as directed, on a wall outlet and clear of bedding. Never run a generator, grill, or camp stove inside the house or in an attached garage.

If the outage looks like it will last, shut off the main water supply and drain the lines by opening the lowest faucets. Hot water or steam boilers also hold water, so ask your technician how to protect that system. Homes that sit empty should have a low-temperature alarm, which can text you before pipes are in danger.

When to Stop Troubleshooting

Stop if you have checked the thermostat, power, filter, fuel, and vents and the system still will not heat, or if you notice soot, a burning smell, or water around the unit. A service call in southern New Hampshire typically runs around $100 to $250 for the visit, with after-hours and weekend rates higher, and the repair adds to that. Common fixes such as a flame sensor cleaning or igniter usually cost a few hundred dollars or less.

You can compare local companies in our New Hampshire HVAC directory and find seasonal maintenance guides on our homeowner blog. A furnace past about 15 to 20 years old with repeat failures deserves a replacement quote alongside the repair. Book that conversation before the next cold snap rather than during it.

Furnace Questions From New Hampshire Homeowners

Why does my furnace run but blow cold air?

Check the thermostat fan setting first, since On keeps the blower going without heat. If it is on Auto, the burner may be locking out on a safety, often from a clogged filter or dirty sensor. A system that keeps cycling this way in January should get a service call the same day.

How long can a New Hampshire house go without heat?

It depends on insulation and the outdoor temperature. A tight house may hold above freezing for a day or more, while a drafty older home in Berlin or Littleton on a subzero night can have frozen pipes in a few hours. Protect the plumbing as soon as you realize repairs will take a while.

Can I add diesel to an empty oil tank in an emergency?

Many heating oil companies say a small amount of diesel can work as a short-term stopgap, because the fuels are similar. Pour it slowly, and ask your oil company first, because you may still need to bleed the line. Never use gasoline, which is dangerous in an oil burner.

Does my furnace need a yearly cleaning if it seems fine?

Yes, plan on one every year, ideally before October. Oil systems in particular build up soot that wastes fuel and leads to nozzle and burner problems. A tune-up also gives a technician a chance to test for carbon monoxide and spot a cracked part before a cold night.